Blog Archives

Installing Workbench and setting automatic scsi.device load on boot

WB_640

Now that we have CF card all set up lets see how to install Workbench and set it to automatically load patched/updated scsi.device so we don’t have to worry if it’s loaded or not.

Read the rest of this entry

Advertisements

Partitioning 16 GB Compact Flash card with WinUAE and PFS3

Cards_640

Lately I’ve noticed a lot of questions on how to partition and prepare Compact Flash card (or HDD) for use with Amiga, so I’ve decided to write this tutorial on how to do it and format them as PFS3 partitions.

At least this is how I do it :). Using PC with WinUAE to prepare everything and just pop finished card in Amiga, ready to go.

Read the rest of this entry

PS/2 mouse to Amiga DB9 adapter

It’s time for something more complicated than rewiring premade stuff. After joysticks and gamepads, next thing that you can’t replace that easy is the mouse. After searching the net for a bit I found the solution on Aminet. Small device with microcontroller (MCU for short) that translates signals from standard PC PS/2 type mouse to signal Amiga understands. I also found versions with USB connector, but it’s actually a bit of deception. “Real” USB mice aren’t supported. As far as I understood there are too many variations in USB implementations to implement USB support with these small microcontrollers. It is possible, but it would need more powerful MCU and would subsequently cost more. It could be made with simple MCU but then it would work only with mouse type that it was tested with during development, even so far that it could happen to work only with that specific model, not the whole brand.

Read the rest of this entry

DIY Joystick/Mouse extension cord

Gamepads from previous article have pretty short cable, unless you’re going to have computer in your lap. All in all not really practical. So, next step is making extension cord.

Basically it’s simple, connect corresponding pins on two connectors (pin 1 from one to pin 1 from the second and so on). Connectors are not the problem, you’ll need one female and one male DB9 connector. They’re pretty standard thing in electronics shop, and there’s bunch of them on ebay.

The real problem is the cable. Joystick connector has 9 pins, that means we’ll need (at least) 9 pin cable, that’s where I got stuck. Here in Croatia there aren’t that many electronics shops and I haven’t found similar cables in shops that sell tools and similar stuff. Problem is that they’re kinda pricey. I’ve found 10 wire round cable but price was almost $3 per meter (one meter is 3.28 feet, you can round it to 3 feet for easier math 🙂 ) . I planned to make two cables of at least 2 meter in length (cca 6 feet), that would make $12 just for the cable. There are cheaper ones, but they’re flat cables and that doesn’t look that practical.

Read the rest of this entry

Cheapo Sega gamepad mod

These days it’s getting hard to find joysticks or gamepads that would work on Amiga, Comodore 64/128 and the rest of the compatible computers. Of course, you can find used ones on ebay and like, but from what I’ve seen most are pretty banged up and/or expensive so I don’t consider them a thing to be relied upon.

Sometimes you can stumble upon new ones, so called NOS, New Old Stock, or if some company makes a series for vintage fans, but again, any option is pricey. In my opinion that makes sense for collection, so you can have everything nice and shiny for display. But if you intend to use it cheaper, more replaceable, stuff would be nice.

 

But luckily there is cheap alternative. Sega Mega Drive 1, 2, 3 (basically the same console) or Sega Genesis as it was called in North America. It uses the same 9 pin DB9 connector as these Commodore computers. They can even work out of the box on them but it’s highly discouraged. Especially in Commodore 64 case where they can kill it.  I’ve seen few versions, for starters I ordered cheapest ones I found on ebay. Price is about $6 for two. They even came in boxes, I expected just the plastic bag 🙂 .

 

Packaging

Packaging

Read the rest of this entry